AutoCAD 2006 Level 1 DAY 2
No Penalty for wrong answers. Best of Luck!
First name:
Last name:
email
1
Which entry will draw a LINE 2" long at an angle of 45 degrees from absolute coordinate 1,1?
@2,45
@2,1.1
2<45
@2<45
@2>45
2
How many coordinate points must you specify to create a rectangle using the RECTANG command?
4
2
1
3
5
3
You plan to put some notes on a house floor plan that will be plotted from model space at 1/8" = 1' (1:96). You want some room labels to show up prominently on the paper drawing in 1/8" (0.125") height for good legibility. What actual height does the label have to be created with in the model to make this happen?
1"
96"
12"
1/96"
11/2"
4
You draw a series of "
POINTS
" at key coordinates supplied to you by a surveyor who measured the location of a fenced in building property's corners. Which running OSNAP do you use to draw a "
PLINE
" fence around the perimeter of this property using the "
POINTS
"?
Endpoint
Center
Node
Point
Quadrant
5
Which AutoCAD template must you select if you plan to use 1 AutoCAD unit as a millimeter in your new model you are starting today?
acad.dwt
acad.dwg
acadiso.dwt
acadiso.dwg
metric.dwt
millimeters.dwt
6
Which of the following is a
relative CARTESIAN
coordinate?
4,5
4<60
@3<30
@4,5
<45,5
7
Which text justification option allows the user to place some text in the center of a circle with equal spacing all around the text to the circle?
Center
Middle Center
Left
Right
Top Center
8
Refer to EKHO's "2D Checklist" Tip Sheet. Which AutoCAD Drawing commands are NOT available in AutoCAD LT? (Check ALL that apply)
IMAGE
LINE
MLINE
PLINE
REGION
INSERT
9
Draw a "
RECTANGLE
" with the 2 corners at the absolute coordinates 4.5,2.625 and 4.925,4.235. Use the "
DIST
" command to measure the diagonal distance between these 2 points. What is the distance?
1.6653
1.6654
1.6655
1.6652
1.6765
10
Which command creates an infinite line in one direction?
PLINE
RAY
XLINE
MLINE
LINE
11
Refer to the EKHO Tip Sheet "2D Checklist". Which AutoCAD Drawing command was first introduced in AutoCAD 2005?
REVCLOUD
ARRAY
MLINE
MTEXT
TABLE
12
Switch to AutoCAD and draw an
ELLIPSE
starting at
5,5
. Specify the other end point of the axis to be
8.125,5.5
. Enter a rotation angle of
60 degrees
. What is the circumference of the ellipse?
7.6651
7.6652
7.7659
7.6654
7.6674
13
What type of object do you create when you use the
RECTANG
command?
RECTANGLE
Closed PLINE
Open PLINE
POLYGON
4 LINES
14
If you trim off both ends of an
XLINE
(construction line) what type of object will you have?
MLINE
RAY
PLINE
LINE
XLINE
15
What is the distance between point 4.4314,5.0489 and point 1.3041,5.049
3.1271
3.1272
3.1273
3.1274
3.7214
16
How many coordinate points must you specify to create a rectangle using the
PLINE
command?
2
3
4
5
1
17
To create a solid "
DONUT
" with an outside diameter of 2" you would:
Set the inside diameter to 2, and the outside diameter to 0.
Set the inside diameter to 0, and the outside diameter to -2.
Set the inside diameter to 0, and the outside diameter to 2.
Set the inside diameter to -2, and the outside diameter to 2.
Set the inside diameter to +1, and the outside diameter to +3.
18
Which command will place a landscape light at 1 meter spacing along a curved garden path?
DIVIDE
CURVE
XLINE
POINT
MEASURE
19
Refer to EKHO's "
2D Checklist
" Tip Sheet. Which AutoCAD editing commands will
NOT
work on the
ELLIPSE
drawing object? (Check
ALL
that apply)
ARRAY
FILLET
BREAK
CHAMFER
COPY
20
Create a hexagon with a 0.90" edge and then OFFSET another one on the outside of it by 0.5678". What is the distance from the 2 furthest points (A - B) closest to?
3.1113
3.1210
3.1310
3.2110
3.4100
Hit Submit to get your score.
Created and managed with SmartLite WebQuiz XP
