AutoCAD Level 1 DAY 2
No Penalty for wrong answers. Best of Luck!
First name:
Last name:
email
1
You want to use 1 AutoCAD unit to represent an inch, but would also like the convenience of inputting coordinates like 12',3'4"-1/4". What type of "
UNITS
" must you select to allow this convenience?
Decimal
Architectural
Engineering
Fractional
Scientific
Feet
2
What model space text height should you use in your text style to plot 0.5
" high text
on a drawing plotted at
1:100
plot scale?
100"
10"
50"
0.25"
1"
3
What type of object do you create when you use the
RECTANG
command?
RECTANGLE
Closed PLINE
Open PLINE
POLYGON
4 LINES
4
What is the distance between point 4.4314,5.0489 and point 1.3041,5.049
3.1271
3.1272
3.1273
3.1274
3.7214
5
Draw a "
RECTANGLE
" with the 2 corners at the absolute coordinates 4.5,2.625 and 4.925,4.235. Use the "
DIST
" command to measure the diagonal distance between these 2 points. What is the distance?
1.6653
1.6654
1.6655
1.6652
1.6765
6
Refer to EKHO's "
2D Checklist
" Tip Sheet. Which AutoCAD editing commands will
NOT
work on the
ELLIPSE
drawing object? (Check
ALL
that apply)
ARRAY
FILLET
BREAK
CHAMFER
COPY
7
You want to draw a floor plan for a gazebo that is a perfect Octagon (8 sides) that will be 14' from outside face to opposite face. Which option of the POLYGON command will help you to do this with a 14' diameter
CIRCLE
?
[Circumscribed about circle]
[Inscribed in circle]
[Edge]
[Face]
[Distance]
8
Create a hexagon with a 0.90" edge and then OFFSET another one on the outside of it by 0.5678". What is the distance from the 2 furthest points (A - B) closest to?
3.1113
3.1210
3.1310
3.2110
3.4100
9
Switch to AutoCAD. Starting at absolute coordinates 0,0, draw a "
LINE
" that is 3.333 units long at an absolute angle of 57.123 degrees. Use the "
ID
" command to determine what are the absolute x,y coordinates of the second endpoint of the LINE?
1.8091,2.7990
1.8092,2.7991
1.8093,2.7992
1.8094,2.7993
2.7993,1.8094
10
How many coordinate points must you specify to create a rectangle using the
PLINE
command?
2
3
4
5
1
11
Refer to the EKHO Tip Sheet "2D Checklist". Which AutoCAD Drawing command was first introduced in AutoCAD 2005?
REVCLOUD
ARRAY
MLINE
MTEXT
TABLE
12
To create a solid "
DONUT
" with an outside diameter of 2" you would:
Set the inside diameter to 2, and the outside diameter to 0.
Set the inside diameter to 0, and the outside diameter to -2.
Set the inside diameter to 0, and the outside diameter to 2.
Set the inside diameter to -2, and the outside diameter to 2.
Set the inside diameter to +1, and the outside diameter to +3.
13
Which text justification option allows the user to place some text in the center of a circle with equal spacing all around the text to the circle?
Center
Middle Center
Left
Right
Top Center
14
You want to draw a line that starts at absolute coordinates 3,4 and move 2" in the vertical direction and 3" in the horizontal direction. What is the correct relative cartesian coordinate to enter?
@2,3
@3,4
@3,2
3,4
@4<45
15
Which command will place a landscape light at 1 meter spacing along a curved garden path?
DIVIDE
CURVE
XLINE
POINT
MEASURE
16
You want to "
INSERT
" a BLOCK that you purchased from an outside supplier and you know it was drawn with 1 AutoCAD Unit = 1", but your design is done in millimeters. What scale value do you use to place this BLOCK accurately in your metric model with the INSERT command?
0.0393701
0.393701
2.54
25.4
1/25.4
17
If you trim off both ends of an
XLINE
(construction line) what type of object will you have?
MLINE
RAY
PLINE
LINE
XLINE
18
Which AutoCAD template must you select if you plan to use 1 AutoCAD unit as a millimeter in your new model you are starting today?
acad.dwt
acad.dwg
acadiso.dwt
acadiso.dwg
metric.dwt
millimeters.dwt
19
What is the default direction in AutoCAD to draw positive angles?
CCW
CW
Left
Right
Up
Down
20
Which entry will draw a LINE 2" long at an angle of 45 degrees from absolute coordinate 1,1?
@2,45
@2,1.1
2<45
@2<45
@2>45
Hit Submit to get your score.
Created and managed with SmartLite WebQuiz XP
